Cuisinart BFP-703 Blender/Food Processor User Manual

Cuisinart BFP-703 Blender/Food Processor

Cuisinart BFP-703 Blender/Food Processor User Manual.

IMPORTANT SAFEGUARDS

When using an electrical appliance, basic safety precautions should always be followed, including the following:

1. Read the Cuisinart BFP-703 Blender/Food Processor User Manual.
2. To protect against the risk of electrical shock, do not put the motor base of the SmartPower Duet® appliance in water or other liquid.
3. This appliance is not intended for use by children or by persons with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge. Close supervision is necessary when any appliance is used near children. Children should be supervised to ensure that they do not play with the appliance.
4. Turn the appliance OFF, then unplug from the outlet when not in use, before assembling or disassembling parts and before cleaning. To unplug, grasp the plug and pull from the outlet. Never pull from the power cord.
   WARNING: Never put your hands into the blender jar/food processor work bowl or container, or handle the blades with the appliance plugged in.
5. Avoid contact with moving parts.
6. Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions, or is dropped or damaged in any manner. Contact the manufacturer at their customer service telephone number for information on examination, repair, or adjustment
7. The use of attachments, other than those recommended by Cuisinart, including canning or ordinary jars not recommended or sold by Cuisinart, may cause fire, electrical shock, or risk of injury to persons.
8. Do not use outdoors.
9. Do not let the cord hang over the edge of the counter or table or touch hot surfaces, which could damage the cord.
10. Keep hands and utensils out of jar/food processor work bowl during use, to reduce the risk of severe injury to persons or damage to the blender itself. A rubber or plastic spatula may be used but must be used only when the blender is turned OFF.
11.  When the motor base is in ON mode, and LED lights are flashing or glowing, do not touch the cutting assembly, interfere with blade movement, or remove the blender jar cover. Accidentally touching a speed button may activate the blender.
12. THE BLADES ARE VERY SHARP. HANDLE CAREFULLY. Store out of reach of children.
13. To reduce the risk of injury, never place the chopping blade/cutting assembly on the base unless the blender jar or food processor work bowl is properly attached.
14. Always operate the blender or food processor with the cover in place.
15. Never leave your blender or food processor unattended while running.
16. When blending HOT liquids in the blender jar, remove the measured pour lid (centerpiece of cover) to allow steam to escape.
17. Twist on the locking ring firmly. Injury can result if moving blades accidentally become exposed.
18. Do not use an extension cord with this unit. Doing so may result in fire, electrical shock, or personal injury.
19. Regarding your cord set: A longer cord has been provided so that you will have flexibility in positioning your Cuisinart® SmartPower Duet® Blender/Food Processor near an electrical outlet. Exercise care when using the longer cord to avoid entangling or tripping over the cord. The longer cord should be arranged so that it will not drape over the counter or tabletop, where it can be pulled on by children or tripped over. Excess cord should be stored in the cord storage area at the back of the blender base, to avoid injury caused by the longer cord.
20. Be certain the food processor cover is securely locked in place before operating the appliance. Never operate without the cover locked securely in place.
21. Do not attempt to defeat the food processor cover interlock mechanism.
22. Never feed food into a processor by hand. Always use the food pusher.
23. Make sure the blade or disc has come to a full stop before removing the cover.
24. This food processor attachment is to be used only with Cuisinart® BFP-703 series blenders. Do not use it with any other manufacturer’s blender base. This appliance is intended for household use only.
25. Wash the blender jar, food processor work bowl, food processor chopping blade, locking ring, and covers before first use.
26. WARNING: TO REDUCE THE RISK OF ELECTRICAL SHOCK OR FIRE, DO NOT REMOVE THE BASE PANEL. NO USER-SERVICEABLE PARTS ARE INSIDE. REPAIR SHOULD BE DONE ONLY BY AUTHORIZED PERSONNEL.
27. Do not operate your appliance in an appliance garage or under a wall cabinet. When storing in an appliance garage always unplug the unit from the electrical outlet. Not doing so could create a risk of fire, especially if the appliance touches the walls of the garage or the door touches the unit as it closes.
    NOTICE: Do not fill the bowl above the marked maximum fill line (or rated capacity) to avoid the risk of injury due to damage to the cover or bowl.

Cuisinart BFP-703 Blender/Food Processor User Manual.

NOTICE
This appliance has a polarized plug (one prong is wider than the other). To reduce the risk of electric shock, this plug will fit into a polarized outlet only one way. If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not modify the plug in any way. The maximum rating of 500 watts is based on the jar attachment that draws the greatest power. Other recommended attachments may draw significantly less power. This unit comes with a resettable thermal fuse to prevent damage to the motor in the case of extreme overload. Simply unplug the unit, rest it for 15 minutes, and continue.

UNPACKING INSTRUCTIONS

Place the gift box containing your Cuisinart® SmartPower Duet® Blender/Food Processor on a flat, sturdy surface before unpacking. Remove the instruction booklet and other printed materials from the top of the corrugated insert. Next, remove the top corrugated insert. It contains the measured pour lid, adapter stem, and the slicing/shredding disc. Carefully remove the slicing/shredding disc, as it is VERY SHARP, then remove the lid and adapter stem. Carefully lift the blender base from the box and set aside. Remove the food processor accessory. Remove the lower corrugated insert containing the blender jar assembly. Be careful not to tip the jar when removing it. Remove any additional literature from the box. To assemble the blender, follow the Assembly instructions on page 5 of this instruction booklet. Replace all corrugated inserts in the box and save the box for repackaging. See the Features and Benefits section of this booklet for a listing of all blender parts. Before using it for the first time: Wash all parts according to the Cleaning and Maintenance section on page 7 of this booklet to remove any dust or residue.

INTRODUCTION

Congratulations! You have purchased two of Cuisinart’s most versatile appliances wrapped in one! The Cuisinart® SmartPower Duet® Blender/Food Processor combines Cuisinart’s top-of-the-line 7-speed Electronic Blender with our legendary Cuisinart® Food Processor. As a blender, the Cuisinart® SmartPower Duet® Blender/Food Processor is the life of the party, engineered with seven speeds that let you purée, blend, mix, stir, and more. One speed is just for crushing ice, though ice can be crushed perfectly at any of the settings. You can make soups, salsas, thick and delicious frozen drinks, baby foods, etc. The blending capabilities are endless! Attach the work bowl and cover and the Cuisinart® SmartPower Duet® Blender/ Food Processor becomes a fully functioning Cuisinart® classic food processor. Chop raw and cooked foods, including meats, to any consistency. The reversible slicing/ shredding disc and feed tube let you make mountains of vegetables, fruits, and most cheeses in minutes. This combination of Cuisinart’s two most versatile appliances promises years of happy and healthy food preparation.

BLENDER FEATURES AND BENEFITS

Cover
Just press on; no turning or twisting is required. Tightfitting seal resists leakage.

2-oz. Measured Pour Lid
Allows you to measure and add ingredients neatly without removing the cover.

40-oz. Glass Jar with Dripless Pour Spout
Has a unique, sturdy, wide-mouth design and a dripless pour spout for no-mess pouring.

Leakproof Rubber Gasket (not shown)
Holds the glass jar snugly in position for safe operation.

High-quality cutting Assembly with Patented Stainless Steel Blades
Is strong enough for all blender tasks, including tough jobs, from ice crushing to chopping delicate herbs.

Note: Blades are very sharp…handle carefully.

Collar (Locking Ring)
The collar is self-aligning so that the glass blender jar slides easily into position, eliminating the frustration of twisting and turning the blender jar to lock it into place.

Heavy-Duty Motor Base
The motor base is so sturdy and stable, that it will not “walk” on your counter – even during ice crushing! The motor is strong enough to handle all blending tasks, including crushing ice without liquid, and is backed by a three-year limited warranty.

7-Speed Touchpad Control with Indicator Lights
Easy to use, read, and clean. Seven speeds give you great versatility – use low speeds for delicate blending up to high speeds for cheese, garlic, or lemon zest. The red LED lights indicate what blender speed you are using.

Pulse Button
Allows you to pulse at any speed from high to low, so you can blend ingredients only as much as needed.

Ice Crush Button (Blender Only)
Activates the ice-crushing speed. This button is preset to the best speed for crushed ice. However, you can crush ice at any speed. The food processor attachment is not intended to crush ice. Use the blender jar for this.

Food Processor Button
Is preset to the best speed for all food processing tasks. Always use this button when food processing. This speed may also be used with a blender jar.

Slip-Proof Feet
Prevent movement during use and prevent damaging marks on countertops or tables.

Hidden Cord Storage Compartment (not shown)
Keeps countertop safe and neat by conveniently storing excess cord.

Impact-Resistant Plastic Housing
Is crafted of the finest quality materials to resist staining, cracking, and odors.

 Innovative Cuisinart® Design
The combination of power, performance, sturdiness, and easy cleanup makes this blender a winner.

BLENDER ASSEMBLY, USE, AND CARE

To use your Cuisinart® SmartPower Duet® Blender/Food Processor, begin by assembling the blender jar.

1. Turn the blender jar (a) upside down, and place it flat on a sturdy surface.
2. Position the rubber gasket (b) on the round opening at the bottom of the blender jar.
3. Turn the cutting assembly (c) upside down, and place the blade end in the blender jar opening. Note: Blades are very sharp, handle carefully.
4. Secure the rubber gasket and cutting assembly in position by placing the smaller opening of the locking ring (d) on top of the cutting assembly. Engage threads by twisting the locking ring clockwise until tightened. Make sure the locking ring is tightly fastened to a blender jar. Once assembled, turn the blender jar right side up.
5. Push the cover onto the top of the blender jar. Insert the measured pour lid into the cover, aligning the tabs in the pour lid with the slots in the cover. Twist clockwise to lock and pour the lid into the cover.
6. Place the blender jar on the motor base so that the jar markings are facing you and the handle is positioned to one side.
7. Plug in the power cord. Your blender is now ready to be used.

Helpful Reminders

• Once the cover is in position, additional ingredients can be added during blending by simply twisting the measured pour lid counterclockwise until the tabs in the pour lid align with the slots in the cover. Pull up the pour lid, add ingredients, and replace the pour lid.
• The cover should always be in place while the unit is ON.
• Warning: Do not place the blender jar on the base while the motor is running.
• Do not twist the locking ring from the blender jar when removing the blender jar from the base. Simply lift the blender jar from the motor base.
• Boiling liquid or solid frozen foods (except ice cubes or ½” pieces of frozen fruit) should never be placed in the blender jar.
• Do not place ice, frozen foods, or very cold liquids in a blender jar that has come directly from a hot dishwasher.
• Do not place very hot liquids or foods in a blender jar that has come directly from the freezer. Boiling liquids should cool for 5 minutes before being placed in a blender jar.
• Follow the Cleaning and Maintenance instructions on page 7 before your first use.

BLENDER OPERATION

1. Place the motor base of your Cuisinart® SmartPower Duet® Blender/Food Processor on a flat, sturdy surface. The surface must be clean and dry. Assemble the blender by following the Assembly instructions. Once the jar is assembled and is in position on the motor base, plug the Cuisinart® SmartPower Duet® Blender/Food Processor into an electrical outlet.
2. Add all necessary ingredients to the blender jar and replace the cover. You may add additional ingredients by lifting the measured pour lid and dropping ingredients through the fill area. Replace the measured pour lid after adding ingredients. Do not place hands into blender jar with blender plugged in.
   Note: Add liquid ingredients first, then follow with solid ingredients. This will provide more consistent blending and prevent unnecessary stress on the motor.
   Tip: Liquid ingredients can be measured in the measured pour lid, using the measurement marking. Solid ingredients can be added by simply dropping them through the fill area into the blender jar. Replace the measured pour lid after adding ingredients.
   Note: To remove the blender jar cover, lift the edge of the cover upward. Lifting the measured pour lid will not remove the cover.
3. To start blending: press the On button. The red LED light will flash, indicating
   that the blender is turned on but no speed has been selected.
4. Press the desired blending speed: both the On indicator light and the activated speed indicator light will glow. The blender will now be functioning at the desired speed. It is possible to switch speeds without pressing the Off button, by simply pushing the next desired speed button.
5. To reset the blender: The unit has an advanced thermal resettable fuse feature. In the event of an overload condition, the unit will shut down to protect the motor from overheating. When this happens, to reset the unit, unplug the blender and let it cool down for a minimum of 15 minutes. Then look to reduce the contents and/ or clear any jams, then restart as noted in the operating directions.
6. To stop the blending process: re-press the activated speed button. The blending process will stop. The red On indicator light will continue to flash to let you know that the blender is still on and can be reactivated by pushing the desired speed button. The blender can be completely deactivated and stopped from any speed by pushing the Off button. You will need to press the On button again to continue blending.
7. Pulse Mode: while the blender is turned on, you can create a burst of power for quick, efficient blending by activating this function. To do so, first push the Pulse button, which will cause the Pulse indicator light to flash. Next, push and release the desired speed button. Repeat as desired. You determine the duration of each pulse. While pulsing, all indicator lights (the On, the Pulse, and the desired speed) will glow. The Pulse function can be used to break apart larger pieces of food or to control the texture of food when chopping. The Pulse function is also effective in starting the blending process when you do not want continuous power, or when processing items that do not require an extended amount of blending.
8. To crush ice: Use a blender jar only. The Cuisinart® SmartPower Duet® Blender/ Food Processor motor is strong enough to crush ice without liquid at any speed; however, for your convenience, we have preset the best speed for ice crushing. To give you greater control, the Ice Crush function automatically operates as a Pulse function. To crush ice, place ice cubes in the blender jar, and place the cover and the measured pour lid on the blender jar. Press the On button. Press the Ice Crush button in short pulses until the ice is crushed to the desired consistency. See the Recipe Tips section on page 12 for more details.
9. To dislodge food: use a rubber or plastic spatula to help remove food lodged around the cutting assembly. DO NOT USE SPATULA UNTIL YOU HAVE TURNED OFF AND UNPLUGGED THE BLENDER. Replace the cover and measured pour lid and continue blending if necessary. Make sure the spatula is not inside the blender jar before blending.
10. When finished blending: press the Off button, and unplug the blender from the electrical outlet. Never remove the blender jar from the motor base until pressing the Off button. Do not twist the locking ring from the blender jar when removing the jar from the motor base. Simply lift the blender jar from the motor base. Do not place hands into blender jar with blender plugged in.

FOR BLENDER FUNCTION

FOR BLENDER FUNCTION

CLEANING AND MAINTENANCE

Always unplug your Cuisinart® SmartPower Duet® Blender/Food Processor from the electrical outlet before cleaning. The blender is made of corrosion-resistant parts that are easy to clean. Before the first use and after every use, clean each part thoroughly. Periodically check all parts before reassembly. If any part is damaged or the blender jar is chipped or cracked, DO NOT USE BLENDER. Remove the blender jar from the motor base by lifting it straight up and away. Twist off the locking ring by turning counterclockwise. Remove the cutting assembly and rubber gasket. Wash in warm soapy water; rinse and dry thoroughly. Place the locking ring in the upper rack of the dishwasher or wash in warm water.

CAUTION: Handle the cutting assembly carefully. It is SHARP and may cause injury. Do not attempt to remove blades from the cutting assembly. Remove the blender jar cover and the measured pour lid. Wash in warm, soapy water; rinse and dry thoroughly, or place in the upper rack of the dishwasher. The blender jar should be washed in warm soapy water and rinsed and dried thoroughly. The blender jar can also be placed upside down in the dishwasher. Finally, wipe the motor base clean with a damp cloth to remove any residue, and dry thoroughly. Never submerge the motor base in water or other liquid, or place it in the dishwasher. Any other servicing should be performed by an authorized service representative.

Tip: You may wish to clean your blender cutting assembly as follows: Squirt a small amount of dishwashing liquid into an assembled blender jar and fill halfway with warm water. Run on Stir for 15 seconds. Repeat using clean tap water. Empty the blender jar and carefully disassemble parts. Wash the cutting assembly, gasket, and locking ring in warm, soapy water. Rinse and dry all parts thoroughly.

DO’s AND DON’Ts WHEN USING YOUR BLENDER/FOOD PROCESSOR

Do:

• Make sure the electrical outlet is rated at the same voltage as that stated on the bottom of the blender motor base.
• Always use the motor base on a clean, sturdy, and dry surface.
• Always add liquid ingredients to the blender jar first, then add the remaining ingredients. This will ensure that ingredients are uniformly mixed.
• When using either appliance, cut most foods into cubes approximately ½” to 1″ to achieve a more uniform result. Cut all cheeses into pieces no larger than ½”.
• When using a blender, use the measured pour lid to measure liquid ingredients such as alcohol. Replace the measured pour lid after the ingredients have been added.
• When using either appliance, use a rubber or plastic spatula as needed, only when the blender is turned OFF. Never use metal utensils, as damage may occur to the blender jar/work bowl or cutting assembly.
• Place blender cover on firmly. Always operate the blender with the cover on.
• Make sure the locking ring is tightly attached to a blender jar.
• After using the blender, always remove the locking ring, cutting assembly, and rubber gasket before cleaning.
• When scraping the blender jar with a spatula, remove the food from the sides of the blender jar and place it in the center of the blender jar, over the cutting assembly.
• When chopping fresh herbs, garlic, onion, zest, bread crumbs, nuts, spices, etc., make sure the blender jar and cutting assembly are completely dry.
• If food tends to stick to the sides of the blender jar or food processor work bowl during use, pulse in short bursts.
• When using a food processor, pulses should be short bursts. Space the pulses so the blades stop rotating between pulses.

Don’t:

• Don’t store food or liquids in your blender jar or food processor work bowl.
• When using a blender, don’t place the cutting assembly and locking ring onto the motor base without the blender jar attached.
• A blender or food processor will not mash potatoes, knead dough, or beat egg whites.
• Don’t remove the blender jar or food processor bowl while the unit is on. Keep the blender jar or food processor cover on while blending.
• Don’t twist the locking ring from the blender jar when removing the blender jar from the motor base. Simply lift the blender jar from the motor base.
• Don’t overprocess foods. A blender or food processor will achieve the most desired results in seconds, not minutes.
• Don’t overload the blender or food processor. If the motor stalls, turn it off immediately, unplug the unit, and remove a portion of the food; then continue.
• Don’t use any utensils inside the blender jar or food processor bowl while the motor is on.
• Don’t use any container or accessories not recommended by Cuisinart. Doing so may result in injury.
• Don’t place your hands inside the blender jar or food processor bowl when the blender is plugged in.
• Don’t add boiling liquids or frozen foods (except ice cubes or ½” pieces of frozen fruit) to a glass blender jar. Boiling liquids should cool for 5 minutes before being placed in the blender jar.
• The food processor accessory is not intended to crush ice. This could damage the chopping blade and will damage the work bowl.

FOOD PROCESSOR FEATURES

1. Food pusher with an oil dispenser
2. Work bowl cover with feed tube
3. Stainless steel chopping blade
4. Stainless steel reversible slicing/shredding disc
5. Adapter stem
6. Clear work bowl
7. Gearbox collar
8. Motor base Used for both the blender jar and the food processor bowl

FOOD PROCESSOR ASSEMBLY, USE, AND CARE

Please note that the bowl with the collar will fit on the base in eight different positions. The handle can be in front or on either side and the feed tube in front, back, or on either side. Directions for use reference a certain position for instructional purposes only.

FOOD PROCESSOR ASSEMBLY FOR CHOPPING, PURÉEING AND MIXING

1. Hold the gearbox collar in one hand and the work bowl handle in the other. Twist the bowl clockwise onto the collar.
2. Place the collar with bowl onto the motor base with the handle facing front.
3. Place the chopping blade over the shaft in the work bowl. The chopping blade should slide easily to the bottom of the bowl. The lower blade will almost touch the bottom of the bowl. BE SURE TO HANDLE THE METAL BLADE WITH CARE AS IT IS RAZOR SHARP!
4. Place food to be processed in the work bowl. Put cover on work bowl, with feed tube at about 11 o’clock. Turn the cover clockwise until it fits into position. The cover lock must be clicked into the locked position before use. If you have trouble fitting the cover on the work bowl, turn the chopping blade hub slightly and replace the cover.
5. The food pusher fits in a feed tube with a more rounded side toward the outside of the bowl. ALWAYS USE PUSHER TO GUIDE FOOD THROUGH THE FEED TUBE. NEVER USE YOUR FINGERS OR SPATULA.
6. Plug your Cuisinart® SmartPower Duet® Blender/Food Processor into a wall outlet. Push the On button and then the Food Processor button to start chopping or puréeing. It is recommended that one hand be placed on the food processor lid while in use, to provide unit stability. If the machine doesn’t start, make sure it is plugged in and the work bowl and cover are locked into place. The food processor will not start until the collar, work bowl, and work bowl lid are locked into place. Nevertheless, always unplug the unit before placing your hands into the food processor bowl.

NOTE: The motor base will start, but the food processor blade will not turn until assembled properly.

FOOD PROCESSOR ASSEMBLY FOR SLICING AND SHREDDING

1. Hold the collar in one hand and the bowl handles in the other. Twist the bowl clockwise onto the collar.
2. Place the collar with bowl onto the motor base with the handle facing front.
3. Place the adapter stem onto the center shaft. To slice: Attach the disc to the stem with the raised edge of the slicer on top. To shred: Attach the disc to the stem with the raised shredding slots on top. Place the slicing/shredding disc onto the shaft with the desired cutting blade facing up. Be sure to handle the metal blade with care, as it is razor sharp.
4. Place cover on work bowl, with feed tube at about 11 o’clock. Turn the cover clockwise until it fits into position. Insert food in the feed tube.
5. Hold the pusher with the more rounded side toward the outside of the bowl and insert it in a feed tube over the food. Always use a pusher to guide food through the feed tube. Never use your fingers or spatula.
6. Plug your Cuisinart® SmartPower Duet® Blender/Food Processor into a household electrical outlet.
7. To remove the cover, unlock it by turning it counterclockwise, then lift it straight up.

FOOD PROCESSOR OPERATION

Your Cuisinart® SmartPower Duet® Blender/Food Processor appliance comes with a Food Processor button. This button is the perfect speed for all your food processing tasks. Always use this speed when using the food processor. You may also use the Pulse button with this function for pulse-chopping. To use your food processor, make sure that the bowl is assembled properly and that the blade or slicing/shredding disc and the cover are locked into place. When you use the control panel, the LED will light next to each button you press. Press the On button. For continuous operation, press the Food Processor button. The motor will start if you have followed assembly instructions. To turn the motor off, press the Food Processor button again or the Off button. For the On/Off operation, called pulse-chopping or pulsing, press the On button, press the Pulse button, and then press and release the Food Processor button the desired number of times. The motor runs as long as you hold the Food Processor button down. The motor stops when you release the control switch. Try it a few times. You control the duration and frequency of pulses by the length of time you hold the Food Processor button down and the rate at which you press it. Allow enough time between pulses to let food in the work bowl fall to the bottom. Always use the Food Processor button for pulse-chopping. Never turn the cover back and forth to start and stop the processor.

USING THE FOOD PROCESSOR TO CHOP, PURÉE, AND MIX

Refer to Food Processor Assembly instructions on page 10.

1. Remove the cover and put food into the work bowl. First, cut food into ¾” pieces. You will get a more even chop if you start with pieces that are all the same size. Put pieces into a work bowl with a metal blade in place. You can put in up to 1 cup of food at a time. If you want to process more, do it in batches.
2. Put on the cover and lock it. Insert pusher. It is recommended that one hand be placed on the food processor lid while in use, to provide unit stability. Press the On button, press the Pulse button, and the Food Processor button (to pulse), then release. Repeat two to three times. Each time the blade stops, let food pieces drop to the bottom of the bowl before pulsing again. This ensures that the blade will chop them at every pulse.

NOTE: The unit has an advanced thermal resettable fuse feature. In the event of an overload condition, the unit will shut down to protect the motor from overheating. When this happens, to reset the unit, unplug the blender and let it cool down for a minimum of 15 minutes.
happens to the food. With the pulse-chopping technique, you can get an even chop without the danger of overprocessing. Check texture by looking through the work bowl. Be careful not to overprocess. For a coarse chop, pulse only a few times.

1. If you want a finer chop or purée, press the On button and then the Food Processor button and let the machine run continuously until the food is chopped as fine as you want it. Check frequently through a clear cover or bowl to avoid chopping too fine. Use a plastic spatula to scrape down any pieces that stick to the inside of the bowl. Onions and other food with a high water content turn into a smooth purée very quickly. Do not over-chop – look at food frequently through the work bowl. To purée, follow the same procedure as for chopping, but let the machine run until the food is a smooth purée. New users are often surprised at how fast the processor works. You will quickly get used to its great speed.
   These are some conditions that affect your results:
   • Size of pieces you put in a bowl – all should be about the same size.
   • Amount of food you process – don’t add too much.
   • Type of processing you choose – continuous or pulse-chopping.

ADDING FOOD WHILE PROCESSING
To add liquid while the machine is running, pour it through an open feed tube. This is especially useful when making mayonnaise or dressings. A small hole in the pusher allows you to add liquids in a very slow, steady stream – useful when making sauces. When you want to add small pieces of food like cheese, meat, or garlic cloves while the machine is running, drop them through an open feed tube.  To prevent spills when adding sugar and other dry ingredients, use a funnel.

REMOVING

PROCESSED FOOD
Before removing processed food, press the Off button and wait for the blade to stop spinning. Then remove the cover by turning it counterclockwise. Never try to remove the cover and work the bowl together; this can damage the work bowl. It is important not to let the metal blade fall out of the work bowl as you empty it.

Here are two ways to prevent it from falling out:

1. Before tilting the bowl, use a spatula to remove food from around the blade. Carefully remove the blade from the plastic hub.
2. Hold the top of the blade in place with a finger or spatula while pouring out processed
   food.

At this point, you may either lift the work bowl off the motor base or hold the collar at the base turn the handle of the bowl counterclockwise, and lift the blade straight up. Your Cuisinart® SmartPower Duet® Blender/Food Processor makes many everyday food preparation tasks much easier and faster. Follow these guidelines to get the best results when using metal blades with the food you prepare most often. Cuisinart BFP-703 Blender/Food Processor User Manual.

NOTE: Occasionally, a piece of food may become wedged between the blade and the work bowl. If this happens, remove the cover, lift the blade out carefully, and remove the wedged piece. Empty the bowl, reinsert the blade, and lock the cover into place. Process smaller amounts of the food at one time.

USING THE FOOD PROCESSOR TO SLICE AND SHRED

1. Assemble the clear work bowl on the collar and base in the usual way. (See page 10.)
2. Pick up the adapter stem. Hold the stem by the side that has the octagon shape (eight-sided) and push the rounded side down as far as it will go on the motor shaft.
3. Place the reversible slicing/shredding disc with the desired cutting edge facing up onto the adapter stem. Always handle slicing/shredding disc by the rim. Never touch sharp cutting blades.
4. Put the cover on the work bowl, lock it into place by twisting it clockwise, and insert food in the feed tube.
5. Insert pusher. Use moderate pressure to push down on the pusher with one hand while using your other hand to push the On button, Pulse button, and hold down the Food Processor button. Slicing and shredding only takes a few seconds. Wait until the disc stops spinning before removing the cover. When it stops, remove the cover before removing the work bowl. Never try to remove the cover and work the bowl together; this could damage the work bowl.
6. Remove the slicing/shredding disc before removing the work bowl. To remove it, grasp the flat top section of the adapter stem and lift it straight up. Holding the work bowl collar, turn the work bowl counterclockwise and lift it straight up to remove it from the base.

CLEANING AND STORING YOUR CUISINART® SMARTPOWER DUET® FOOD PROCESSOR ATTACHMENT
Store the chopping blade and slicing/ shredding disc as you would sharp knives – out of the reach of children. The work bowl, cover, pusher, chopping blade, and slicing/shredding disc are top-shelf dishwasher safe. When placing parts in your dishwasher, insert the work bowl upside down. Remember where you place the sharp blade and disc, and be certain to unload the dishwasher carefully. The gearbox collar is not immersible. To clean, just wipe with a damp cloth. If you wash the blades and discs by hand, do it carefully. Avoid leaving them in soapy water where they may disappear. To clean the metal blade, fill the work bowl with soapy water, hold the blade by its plastic center, and move rapidly up and down on the center shaft of the bowl. The use of a spray hose is also effective. If necessary, use a brush. The work bowl should not be placed in a microwave oven.

General Guidelines for Preparing Foods for Slicing and Shredding

WARRANTY

LIMITED THREE-YEAR WARRANTY
This warranty is available to consumers only. You are a consumer if you own a Cuisinart® SmartPower Duet® Blender/Food Processor that was purchased at retail for personal, family, or household use. Except as otherwise required under applicable law, this warranty is not available to retailers or other commercial purchasers or owners. We warrant that your Cuisinart® SmartPower Duet® Blender/Food Processor will be free of defects in materials and workmanship under normal home use for 3 years from the date of original purchase. We suggest you complete and return the enclosed product registration card promptly to facilitate verification of the date of the original purchase. However, the return of the product registration card does not eliminate the need for the consumer to maintain the original proof of purchase to obtain the warranty benefits. If you do not have proof of purchase date, the purchase date for purposes of this warranty will be the date of manufacture. If your Cuisinart® SmartPower Duet® Blender/Food Processor should prove to be defective within the warranty period, we will repair it, or if we think it necessary, replace it. To obtain warranty service, simply call our toll-free number 1-800-726-0190 for additional information from our Customer Service Representatives, or send the defective product to Customer Service at Cuisinart, 150 Milford Road, East Windsor, NJ 08520. To facilitate the speed and accuracy of your return, please enclose $10.00 for shipping and handling of the product. Please pay by check or money order (California residents need only supply proof of purchase and should call 1-800-726-0190 for shipping instructions). Cuisinart BFP-703 Blender/Food Processor User Manual.

NOTE: For added protection and secure handling of any Cuisinart® product that is being returned, we recommend you use a traceable, insured delivery service. Cuisinart cannot be held responsible for in-transit damage or for packages that are not delivered to us. Lost and/ or damaged products are not covered under warranty. Please be sure to include your return address, daytime phone number, description of the product defect, product model number v(located on the bottom of the product), original date of purchase, and any other information pertinent to the product’s return.

CALIFORNIA RESIDENTS ONLY:
California law provides that for In-Warranty Service, California residents have the option of returning a nonconforming product (A) to the store where it was purchased or (B) to another retail store that sells Cuisinart® products of the same type. The retail store shall then, at its discretion, either repair the product, refer the consumer to an independent repair facility, replace the product, or refund the purchase price less the amount directly attributable to the consumer’s prior usage of the product. If the above two options do not result in the appropriate relief to the consumer, the consumer may then take the product to an independent repair facility if service or repair can be economically accomplished. Cuisinart and not the consumer will be responsible for the reasonable cost of such service, repair, replacement, or refund for nonconforming products under warranty.

California residents may also, according to their preference, return nonconforming products directly to Cuisinart for repair, or if necessary, replacement, by calling our Consumer Service Center toll-free at 1-800-726-0190. Cuisinart will be responsible for the cost of the repair, replacement, shipping, and handling of such products under warranty.

BEFORE RETURNING YOUR CUISINART® PRODUCT
If you are experiencing problems with your Cuisinart® product, we suggest that you call our Cuisinart® Service Center at 1-800-726-0190 before returning the product to be serviced. If servicing is needed, a Representative can confirm whether the product is under warranty and direct you to the nearest service location. Your Cuisinart® SmartPower Duet® Blender/Food Processor has been manufactured to the strictest specifications and has been designed for use only in 120-volt outlets and only with authorized accessories and replacement parts. This warranty expressly excludes any defects or damages caused by attempted use of this unit with a converter, as well as use with accessories, replacement parts, or repair services other than those authorized by Cuisinart. This warranty does not cover any damage caused by accident, misuse, shipment, or other than ordinary household use. This warranty excludes all incidental or consequential damages. Some states do not allow the exclusion or limitation of these damages, so these exclusions may not apply to you. You may also have other rights, which vary from state to state. Cuisinart BFP-703 Blender/Food Processor User Manual.

Important: If the nonconforming product is to be serviced by someone other than Cuisinart’s Authorized Service Center, please remind the servicer to call our Consumer Service Center at 1-800-726-0190 to ensure that the problem is properly diagnosed, the product is serviced with the correct parts, and the product is still under warranty.

Trademarks or service marks of third parties referred to herein are the trademarks or service marks of their respective owners. ©2019 Cuisinart East Windsor, NJ 08520 Printed in China 19CE064750 IB-9570-ESP-B

Get More Manuals